COMPARISON
Rack pulley kits compared by rack, plates and height
Of the 12 kit-and-rack combinations compared here, only the PRx Elite High on the PRx Fold-In ONE has a confirmed upper mounting point. Its strap loops over the adjustable pull-up bar. The Elite Low is a separate attachment that mounts in a lower upright hole of at least 5/8 inch. PRx pulley mounting specifications
The Fold-In ONE requires a ceiling at least 91 inches high. Measure the installed bar height and the travel you need for the plates before choosing a cable setup. PRx rack dimensions
The linked US package includes the high pulley and a 72-inch cable. For both high and low pulls, check the package contents before ordering. PRx Elite High package on Amazon
EDITOR’S PICKS
Our top picks
Compare the size, setup, and limitations of each pick. Follow “Specs & sources” for the measurements behind it.
- 1Two cable lengthsMikolo LAT and Lift Pulley SystemAmazon
- 2Strap-loaded platesBells of Steel Cable PulleyAmazon
- 3Two pulley blocks includedSERTT Weight Cable Pulley SystemAmazon
#1Two cable lengths
IllustrationPlate connection
1 or 2 in bore
Loading pin with removable Olympic sleeve and supplied clamp.
Mikolo
LAT and Lift Pulley System
Capacity 280 – Upgrade · one pulley, two cables
The 70 and 90 in cables let you choose a starting position. The pin takes Olympic plates with the sleeve fitted.
#2Strap-loaded plates
IllustrationPlate connection
1 or 2 in bore
Thread the supplied loading strap through the plate center and clip it back to the cable.
Bells of Steel
Cable Pulley
Single pulley kit · 77.4 in cable
The fabric strap passes through the plates, so there is no loading pin to store. One kit supplies a single high pulley.
#3Two pulley blocks included
IllustrationPlate connection
1 or 2 in bore
Convertible loading pin with a removable Olympic sleeve and a plate clip.
SERTT
Weight Cable Pulley System
Black · two pulleys, three cables
Two blocks and three cables give more routing options. The plate adapter accepts the same Olympic plates used on your barbell.
Mikolo supplies two interchangeable cables for a single high pulley. Bells of Steel uses a strap through the plates. SERTT includes two pulley blocks for routes that need a second anchor. Compare mounting points for each kit and rack.
Compare the four kits
| Model | Rack mounting | Supplied cables | Plate connection | Kit load limit | Source |
|---|---|---|---|---|---|
| Bells of Steel Cable PulleySingle pulley kit · 77.4 in cableStrap-loaded platesCheck price on Amazon | Loop the anchor strap over an approved rack bar. The maker’s low-row setup takes two kits. | 77.4 in | 1 or 2 in bore. Thread the supplied loading strap through the plate center and clip it back to the cable. | 440 lb (plate load) | Bells of Steel cable specifications and mountingManufacturer-reported · Bells of Steel US listing and plate fit |
| Mikolo LAT and Lift Pulley SystemCapacity 280 – Upgrade · one pulley, two cablesTwo cable lengthsCheck price on Amazon | Hang the pulley by its strap from an approved rack bar. A straight bar and triceps rope are included. | 70 in + 90 in | 1 or 2 in bore. Loading pin with removable Olympic sleeve and supplied clamp. | 280 lb (loading pin) | Mikolo kit contents and cable lengths on AmazonManufacturer-reported · Mikolo loading pin and plate sizes |
| PRx Performance Elite High PulleyHigh pulley only · triceps rope · 72 in cableCheck price on Amazon | Loop the supplied strap over the Fold-In ONE’s adjustable pull-up bar. PRx confirms this upper mounting point. | 72 in | 2 in bore. Plates slide onto the 13.5 in Olympic loading post. | 600 lb (high pulley system) | PRx high pulley package contents on Amazon.comManufacturer-reported · PRx high and low pulley mounting on the Fold-In ONE |
| SERTT Weight Cable Pulley SystemBlack · two pulleys, three cablesTwo pulley blocks includedCheck price on Amazon | Hang a block by its strap for high pulls. A route using both blocks needs an approved anchor at each attachment point. | 55.1 in + 2 × 70.8 in | 1 or 2 in bore. Convertible loading pin with a removable Olympic sleeve and a plate clip. | 330 lb (loading pin) | SERTT black two-pulley kit on AmazonManufacturer-reported · SERTT plate adapter and loading-pin rating |
The black SERTT kit has a 55.1 in cable, two 70.8 in cables and two 19.7 in extension chains. Use the dimensions for the cable and route you plan to assemble. SERTT parts diagram.
Which kits can you hang from each rack?
Confirmed upper mount · PRx Performance Elite High Pulley on the PRx Performance Fold-In ONE. Adjustable pull-up bar between the uprights.
11 of 12 exact pairings need rack-maker confirmation. The table identifies the upper bar for each kit. A kit’s load rating applies to the part named in its specifications.
| Rack and upper point | Bells of Steel Cable Pulley | Mikolo LAT and Lift Pulley System | PRx Performance Elite High Pulley | SERTT Weight Cable Pulley System |
|---|---|---|---|---|
| Mikolo Folding Wall Mounted Squat RackQuick-attach pull-up bar between the uprights | UnconfirmedBells shows its strap over a rack pull-up bar. Mikolo gives no rating for that strap on the QJ01 bar.Open this pair in the finder | Rack family documented · exact kit unconfirmedThe 280 lb kit lists pull-up bars. The QJ sheet names a pulley add-on without a kit number. Mikolo’s current two-block, 330 lb kit is a different model.Open this pair in the finder | UnconfirmedPRx supplies a pull-up bar strap. Mikolo’s QJ documentation does not identify the Elite High for the QJ01 quick-attach bar.Open this pair in the finder | UnconfirmedSERTT lists pull-up bars as upper anchors. The QJ sheet does not identify either SERTT block or a lower attachment point.Open this pair in the finder |
| PRx Performance Fold-In ONEAdjustable pull-up bar between the uprights | UnconfirmedThe Bells kit uses a strap. PRx names its own Elite for this rack and gives no Bells-specific anchor rating.Open this pair in the finder | UnconfirmedPRx documents the bar for its own Elite High. It gives no mounting approval for the Mikolo 280 lb kit.Open this pair in the finder | Confirmed by rack makerPRx specifies looping the supplied strap over this bar. The Amazon.com listing includes the high pulley only.Open this pair in the finder | UnconfirmedPRx identifies its own high strap and low mounting hardware. Neither attachment is documented for the black SERTT kit.Open this pair in the finder |
| Titan Fitness T-3 Series Folding Power Rack1.25 in pull-up bar, part 2 in the rack manual | UnconfirmedBells describes a high rack bar. Titan does not list the Bells strap for the 82 × 21 in folding model.Open this pair in the finder | UnconfirmedMikolo lists pull-up bars. Titan gives no mounting approval for its strap on the pinned T-3 folding bar.Open this pair in the finder | UnconfirmedPRx supplies a pull-up bar strap. Titan’s 401226 manual does not specify an Elite High strap position or load on its pinned bar.Open this pair in the finder | UnconfirmedTitan documents neither a SERTT strap on part 2 nor a lower SERTT block on this folding rack.Open this pair in the finder |
Upper and lower mounting points in the rack maker’s instructions
| Rack in this guide | Frame and ceiling | Mounting documentation |
|---|---|---|
| Mikolo Folding Wall Mounted Squat RackQJ01 · black · 2 × 2 in · with safety catches | 85.8 in / 217.932 cm frame.Pull-up bar separately listed at 89 in / 226.06 cm. Measure the installed bar.Installation ceiling minimum unpublished. | Upper point · Quick-attach pull-up bar between the uprights. Mikolo lists a cable pulley add-on for its QJ family. That sheet describes 14-gauge steel. The black QJ01 listing specifies 13-gauge uprights and gives no suspended load for its bar. Low route · Mikolo identifies a landmine for barbell rows. The QJ01 documents reviewed give no lower point for a cable pulley. Reviewed . Rack specifications · Mikolo QJ family add-ons · Mikolo’s current 330 lb kit |
| PRx Performance Fold-In ONE90 in · black · adjustable pull-up bar | 90 in / 228.6 cm frame.Minimum ceiling 91 in / 231.14 cm. | Upper point · Adjustable pull-up bar between the uprights. PRx explicitly hangs its own Elite High Pulley by a strap over the Fold-In ONE pull-up bar. Its compatibility FAQ leaves other brands’ accessories unverified. Low route · The Elite Low mounts in a lower upright hole (5/8 in or larger). PRx sells the rack lock separately to keep the upright from lifting. Both Amazon Shop Direct links below take you to PRx for checkout. PRx describes the lock as optional for general pulley use. For cable belt squats, it specifies locking the upright that carries the low pulley. PRx documents no lower strap point for the third-party kits here. Reviewed . Rack specifications · Fold-In ONE Elite high and low system · PRx rack lock specifications · 1 rack lock (one upright) on Amazon Shop Direct · 2 rack locks (one per upright) on Amazon Shop Direct · PRx cable belt-squat setup · PRx pulley and accessory FAQ |
| Titan Fitness T-3 Series Folding Power Rack82 in height · 21 in depth | 82.375 in / 209.2325 cm frame.Installation ceiling minimum unpublished. | Upper point · 1.25 in pull-up bar, part 2 in the rack manual. Step 2 of the 401226 manual pins this bar to the uprights with part 3. Titan identifies it for pull-ups. The manual gives no pulley strap position or suspended-load rating on it. Low route · Titan specifically excludes its bolt-on TRIPLLY-LOWPLLY (SKU 400068) from folding racks. Its accessory guidance identifies no lower mount for the kits compared here. Reviewed . Rack specifications · Titan 401226 operator’s manual, step 2 · Titan T-3 accessory guidance, SKU 400068 |
What each kit needs for low rows
- Bells of Steel Cable Pulley · Bells uses a second separately purchased kit for its low-row route. A lower anchor for that route still needs rack-maker confirmation.
- Mikolo LAT and Lift Pulley System · This one-block kit shows pull-down and lift configurations. Its instructions give no fixed lower mounting point on these racks.
- PRx Performance Elite High Pulley · Low rows on the Fold-In ONE use the separate Elite Low Pulley and its cable. We could not verify a US Amazon listing for the low attachment on November 21, 2026.
- SERTT Weight Cable Pulley System · Both blocks are included. A route with a fixed lower block also needs a documented lower attachment point.
Which of our plates fit?
| Plate in this guide | Bells of Steel Cable Pulley | Mikolo LAT and Lift Pulley System | PRx Performance Elite High Pulley | SERTT Weight Cable Pulley System |
|---|---|---|---|---|
| CAP Barbell Elite Olympic Grip PlateOne 45 lb plate, 17.1 in across and 1.3 in thick. Check clearance from the wall as it rises. | Fits · 2 in bore | Fits · 2 in bore | Fits · 2 in bore | Fits · 2 in bore |
| CAP Barbell Economy Speckled Bumper Plate SetChoose individual bumpers from the 260 lb set. A 45 lb bumper is 2.6 in thick and 17.9 in across. | Fits · 2 in bore | Fits · 2 in bore | Fits · 2 in bore | Fits · 2 in bore |
| Signature Fitness Olympic Cast Iron SetUse individual plates from the 255 lb plate assortment. The advertised 300 lb includes the 45 lb bar. | Fits · 2 in bore | Fits · 2 in bore | Fits · 2 in bore | Fits · 2 in bore |
Choose the plates individually. Allow room to secure them on the pin or strap and to clear the wall throughout the lift. Use the lowest rating among the kit, its attachments and the approved rack anchor.
How much height does the pulley need?
The kit makers publish cable lengths. Ceiling height determines whether the rack can stand in the room. To find the height needed for a pull, measure the installed bar, the hardware below it and how far the loaded plates need to rise.
For example, with the anchor 76 in above the floor, 8 in of hardware below it and the top of the loaded pin starting 20 in above the floor, a 30 in plate rise leaves 18 in overhead. Use your own rack measurements to check pulley height and plate travel.
Before folding the rack
Unload the plates, detach the kit and stow the cables clear of the folding joints. If you plan to keep it on a shelf, measure the packed kit with the rigid attachments inside. The listings do not give a complete size for that arrangement. Select your kit and enter its packed dimensions in the storage finder.